0086-371-67660555  Email:sales@zxcrusher.com
cone crusher nerws banner

position: Home > News > Crusher equipment for use precautions and maintenance

Crusher equipment for use precautions and maintenance

Time:2015-07-27 07:42:50 10:10:46 AM Num:84

    Crusher equipment if for long periods, or used without the correct way to operate and maintain normal production for the future, will bring an impact. In order to make the broken equipment to work, improve work efficiency, and now we introduce it in all aspects of precautions and maintenance methods.

sping cone crusher


       First, if the device is a long time out, antirust primary job is to device the device off the surface of the paint again repaired. Inside the machine regularly exposed parts butter, guarantee that these parts flexible operation. Firstly, rust-proof primary job is to device the device off the surface of the paint again repaired. Inside the machine regularly exposed parts butter, guarantee that these parts flexible operation.

      Second, the storage location of mining machinery should be appropriate. If the conditions then it is best to store the device in dry and ventilated room. If there are no conditions, but also choose the flat ground and put a plank, which can prevent mechanical equipment from moisture. It covers the same time to use anti-rain cover equipment. Second, the storage location of mining machinery should be appropriate. If the conditions then it is best to store the device in dry and ventilated room. If there are no conditions, but also choose the flat ground and put a plank, which can prevent mechanical equipment from moisture. It covers the same time to use anti-rain cover equipment.

Third, let go of the cooling water in the engine, engine oil change, have the fuel tank of diesel equipment to fill the fuel tank to prevent rusting. Third, let go of the cooling water in the engine, engine oil change, have the fuel tank of diesel equipment to fill the fuel tank to prevent rusting.

◆ Preparation before crusher start and precautions
1, should be carefully examined bearing lubrication is good, whether the bearing and connecting brackets have enough grease;
2, should carefully check all fastening are fully tightened;
3, the drive belt is good, there discovered a belt breakage should be replaced when there is oil on the belt or pulley, apply a clean cloth to wipe;
4, protective equipment is good, guards found unsafe, should immediately eliminate it;
5. Check whether the ore crushing cavity or other debris, if any ore or other debris when it should eliminate.

◆ Start Precautions crusher
1, upon inspection, the claimant and the transmission part normal before start-up;
2, the machine only promise to start under no load conditions;
3, after the start, if found to have abnormal situation should immediately stop after the start, we must identify and eliminate abnormal situation, before re-starting the crusher.

◆ maintenance and use precautions crusher
1, after the rock breaking machine functioning, before the beginning of the feed;
2, the material should be crushed evenly added crusher cavity, and should avoid feeding side to prevent sudden load change or unilateral sudden increase;
3, under normal circumstances, the bearing temperature rise should not exceed 35 oC, maximum temperature must not exceed 70 oC. If more than 70 oC should immediately stop, investigate the cause to eliminate it;
4, parking in front, you should first stop feeding work, to be the crushing cavity material to be broken completely discharged only after the close of the motor;
5, in use, if the issues caused by the crushing cavity material blocking parking, should immediately turn off the motor, after the material must be eliminated before the restart;
6, one end of the jaw plate wear can turn around and use.

◆ Lubrication Caution crusher
1, the constant attention and timely manner lubrication friction surface, can only be assured the normal operation of the machine and prolong life;
2, stone crusher generally use calcium-based grease, users can use the machine depending on the location, the temperature and other conditions to choose other types of grease, but it must be protected by good bearing lubrication;
3, added to the bearing grease 50-70% of its volume must be replaced every three months. The application of clean gasoline or kerosene carefully cleaned and ball bearing slide oil change;
4, the bracket pad in contact with the bracket must be injected grease before starting the machine.

Search


Contact us